SageTV Community  

Go Back   SageTV Community > SageTV Products > SageTV Software

Notices

SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.)

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 06-05-2010, 01:36 PM
ptzink ptzink is offline
Sage Aficionado
 
Join Date: Mar 2008
Posts: 299
Updating Existing Recordings to a UNC Path

I am full of them today. So I am finally upgrading from a stand alone server configuration to a server/client config. I am having issues with comskip not functioning on the client and have discovered this is because my recording directories are local and not UNC paths. So here is what I did:
1. Shut down server UI and service
2. Backed up sage.properties and wiz.bin on server
3. Restarted SageTV service and UI on server
4. Changed the recording directories from local paths (eg. d:\TV Shows) to UNC paths (eg. \\sagetv\TV Shows) per the sticky here.
5. Shut down UI and service on server
6. Edited sage.properties file to advanced_video_file_recovery=true
7. Restarted SageTV service and UI on server
After all this, Sage still says the old recordings are located on "d:\TV Shows\*.mpg". The instructions in the FAQ sticky are a little unclear since they assume you are moving your old recordings to a new directory rather than just updating to a UNC path and leaving the recordings where they are. I would really like to update the old/archived recording paths so I can retain comskip playback. Any suggestions? Thanks.
Reply With Quote
  #2  
Old 06-05-2010, 09:40 PM
Opus4's Avatar
Opus4 Opus4 is offline
Administrator
 
Join Date: Sep 2003
Location: NJ
Posts: 19,596
Please read that FAQ again, especially the note at the end that points you to the next FAQ.

- Andy
__________________
SageTV Open Source v9 is available.
- Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1.
- Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus
- HD Extenders: A) FAQs B) URC MX-700 remote setup
Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
Reply With Quote
  #3  
Old 06-05-2010, 10:46 PM
ptzink ptzink is offline
Sage Aficionado
 
Join Date: Mar 2008
Posts: 299
Thanks Opus, I read that post after. However, it assumes (at least the way I read it) that you are moving the files to a different directory. In my setup, I didn't want to move the files, just change from "d:\TV Shows" to "\\sagetv\TV Shows" which are the exact same location.
I think I am going to go a different route to get comskip to work. I was having major video artifacts/choppiness when watching live tv on the client when using UNC paths for recording directories. When I switched my recording directories back to local paths (eg. d:\TV Shows), it resolved the playback problems. So on the client, I have just mapped the exact same network drive letters as the local paths on the server. Seems like a bit of a hack, but it is working well. If you have any other suggestions, let me know.
Thanks!
Reply With Quote
Reply

Tags
client, comkip, unc path


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump

Similar Threads
Thread Thread Starter Forum Replies Last Post
UNC path help APillowOfClouds SageTV Software 12 02-24-2009 01:25 AM
How do you specify UNC path for video storage? svemuri SageTV Linux 2 02-06-2008 04:01 AM
UNC Path issue Wrx4me SageTV Software 5 11-28-2005 05:44 PM
How to create a UNC path ? Box8489 SageTV Software 3 04-13-2005 10:13 AM
UNC drive path and mount Wakecrash SageTV Customizations 0 02-25-2005 11:32 PM


All times are GMT -6. The time now is 07:15 AM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright 2003-2005 SageTV, LLC. All rights reserved.