|
|
|||||||
| SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.) |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
07-22-2005, 05:05 PM
|
|||
|
|||
|
How do I set capture card preference?
Rite now I have a svideo encoder card and two tv tuner cards. I would like to make it so that the svideo card is the card that always records the channels first followed by the two analog cards.
|
|
#2
07-22-2005, 05:12 PM
|
||||
|
||||
|
Check out the mmc/encoders/<some number>/encoder_merit=<value> properties for each capture device, in Appendix A of the PDF manual. Higher <value> is higher priority.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#3
07-23-2005, 07:52 AM
|
|||
|
|||
|
I have tried to set different values for the encoder merit but every time I open and close the properties file it defaults back to 0
|
|
#4
07-23-2005, 07:54 AM
|
||||
|
||||
|
You have to comepletely exit SageTV before editing sage.properties. (And stop the service if using service mode.)
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#5
07-23-2005, 11:55 AM
|
|||
|
|||
|
gotcha the services is what got me
|
|
#6
09-11-2005, 10:28 AM
|
|||
|
|||
|
I have had some problems with this over the last couple of months.
I have 3 tuners 2 analog 1 digital When I am recording a favorite and I try and watch TV sage will say that there is a recording conflict and asks if I would like to keep recording or watching what I want to watch. This is quite frustrating and have yet to figure it out.
|
|
#7
09-11-2005, 02:24 PM
|
||||
|
||||
|
That's a known side effect of setting tuner priorities -- live TV will walk through each tuner in priority order, asking what you want to do if each one is use, until it find an unused tuner, you override a recording, or it runs out of tuners to try.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
