SageTV Community  

Go Back   SageTV Community > SageTV Products > SageTV Software
Forum Rules FAQs Community Downloads Today's Posts Search

Notices

SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.)

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 04-19-2006, 08:32 AM
sgraves66 sgraves66 is offline
Sage User
 
Join Date: Apr 2006
Posts: 33
Video window (some channels) issues

On some channels, mostly HD, there is a vertical green line present.
On others, non-HD, there is a distorted black/white signal across the top of the video window. Very annoying and distracting. Media Center 2005 and BeyondTV do not exhibit these behaviors, but Sage is my personal favorite, so I'd like to know how to adjust the video window to get rid of these problems.
Reply With Quote
  #2  
Old 04-19-2006, 08:43 AM
Opus4's Avatar
Opus4 Opus4 is offline
Administrator
 
Join Date: Sep 2003
Location: NJ
Posts: 19,624
I don't know about the vertical green line (unless it is at the very edge of the screen, in which case, the next solution will also work), but for the line at the top of the screen, see: Small black-and-white dotted line at the top of all channels watching livetv.

- Andy
__________________
SageTV Open Source v9 is available.
- Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1.
- Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus
- HD Extenders: A) FAQs B) URC MX-700 remote setup
Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
Reply With Quote
  #3  
Old 04-19-2006, 11:57 AM
sgraves66 sgraves66 is offline
Sage User
 
Join Date: Apr 2006
Posts: 33
I've tried adjusting these with successful results on one channel, but now, most of the other channels are being cut-off (not seeing full video). Is there a per-channel setting for this? I tried the same channels in BeyondTV again with no problems. Must be something else that can be done.
Reply With Quote
  #4  
Old 04-19-2006, 12:08 PM
Opus4's Avatar
Opus4 Opus4 is offline
Administrator
 
Join Date: Sep 2003
Location: NJ
Posts: 19,624
It is a universal setting used for the Aspect Ratio that you set it for. (Each AR uses its own stretch & offset values.)

The 'missing' video with that distorted line is actually what is in the overscan area on a regular TV, so you wouldn't normally see the portion outside the TV's display area. It only becomes an issue when you know it is there in the recording.

- Andy
__________________
SageTV Open Source v9 is available.
- Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1.
- Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus
- HD Extenders: A) FAQs B) URC MX-700 remote setup
Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
Reply With Quote
  #5  
Old 04-19-2006, 12:43 PM
sgraves66 sgraves66 is offline
Sage User
 
Join Date: Apr 2006
Posts: 33
The 'missing' video on the distorted channel is fixed (only a few channels had this problem), it's other channels that are now missing parts of valid video. (i.e. Weather channel is cut-off on the top where the time should be displayed). Do I need to go back to modify the aspect settings for these channels?
Reply With Quote
  #6  
Old 04-19-2006, 12:55 PM
Opus4's Avatar
Opus4 Opus4 is offline
Administrator
 
Join Date: Sep 2003
Location: NJ
Posts: 19,624
There is no per-channel aspect ratio settings. My guess is that you changed the settings too much so that more of the video is off the screen than needs to be.

- Andy
__________________
SageTV Open Source v9 is available.
- Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1.
- Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus
- HD Extenders: A) FAQs B) URC MX-700 remote setup
Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
Reply With Quote
Reply


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -6. The time now is 05:34 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2023, vBulletin Solutions Inc.
Copyright 2003-2005 SageTV, LLC. All rights reserved.