|
|
|||||||
| SageTV Placeshifter Discussion related to the SageTV Placeshifter application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV Placeshifter software application should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#2
01-24-2007, 09:44 PM
|
||||
|
||||
|
Why are you using port 0? Exactly what are you trying to do? Maybe something is missing or should be done differently.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request. 
|
|
#3
01-25-2007, 07:19 AM
|
|||
|
|||
|
My Network
It occurs to me that it might be my network....
Modem/DHCP Server to 192.168.1.x>>>>WRT 54g Router/AP(Port Forwarding) Then off of that Router I have Two other Routers/AP.... One is a AP for Sputnik which manages a portal on 192.168.2.x The last Router is a WDS Bridge to a Hauppage MVP. Modem>WRT54G (Port Fowarding) > All Comuputers ..............>WRT54G WDS Bridge ..............>WRT54G AP/Sputnik POrtal Is something in conflict....
|
|
#4
01-25-2007, 08:55 AM
|
||||
|
||||
|
I don't know what to say about the network router setup, but what I was trying to point out above was that you shouldn't need to forward the placeshifter connection from or to port 0. The external port used for Placeshifter needs to be forwarded to port 31099 at the local IP address where your SageTV server is located.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#5
01-25-2007, 12:54 PM
|
|||
|
|||
|
Ok, So the Main Router, the one the sage server is connected to, is forwarding that port, but to no avail....
My eror reads The locator server connected to the IP address registered for this locator ID, but could not access the Placeshifter Server's Port. Make sure the port is not blocked on your router/firewall and it is forwarded to your sage tv server computer. ed 
|
|
#6
01-25-2007, 01:27 PM
|
||||
|
||||
|
Is there a firewall on your server PC that is blocking SageTV?
Go to Detailed Setup -> Advanced -> Config Placeshifter Internet Connection, wait for the info to update, then highlight the top button. What info does it list? And, what does it say when you test the connection from the option on that screen? - Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#7
01-25-2007, 08:16 PM
|
|||
|
|||
|
My Sage TV Error is....
The locator server connected to the IP address registered for this locator ID, but could not access the Placeshifter Server's Port. Make sure the port is not blocked on your router/firewall and it is forwarded to your sage tv server computer.
|
|
#8
02-02-2007, 08:01 PM
|
||||
|
||||
|
I have the same issue since i changed from a dlink to a linksys router.
Port 31099 is forwarded and i can connect from the internet via a DynDNS url but not via the locator server (even though the server manager says "locator found server").
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
