|
|
|||||||
| SageTV Software Discussion related to the SageTV application produced by SageTV. Questions, issues, problems, suggestions, etc. relating to the SageTV software application should be posted here. (Check the descriptions of the other forums; all hardware related questions go in the Hardware Support forum, etc. And, post in the customizations forum instead if any customizations are active.) |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
12-21-2004, 03:13 PM
|
||||
|
||||
|
SageTV 2.1 and Recording Conflicts
I just upgraded to SageTV 2.1 and everything went fine except that now I get a lot of recording conflicts that I didn't used to get. I can can get rid of the conflicts by going to the Setup Wizard and clicking on Complete Source Setup but they will reappear the next few times I go into Recording Schedule.
It is almost as if SageTV 2.1 can't remember that it has a network encoder on another system. Anyone have any ideas? Karen
__________________
Intel Pentium 4@2.4 GHz Gigabyte GA8-IHXP 768 MB RDRAM NVidia GeForceX 5700 Hauppage WinTV PVR-350 1 TB Hard Drive space 
|
|
#2
12-21-2004, 04:01 PM
|
||||
|
||||
|
I don't remember whether that was one of the glitches in v2.1, but it did seem to have some tuners problems. There is a link to a new v2.1 dll here. Also, have you tried the latest beta (v2.2.2) to see if it still occurs? If you do try it, be sure to keep backup copies of your properties files & wiz.bin, in case you decide to revert to a previous version.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#3
12-21-2004, 06:00 PM
|
||||
|
||||
|
Andy,
Thanks for the help! Looks like that fixed the problem. Karen
__________________
Intel Pentium 4@2.4 GHz Gigabyte GA8-IHXP 768 MB RDRAM NVidia GeForceX 5700 Hauppage WinTV PVR-350 1 TB Hard Drive space
|
|
#4
01-08-2005, 05:09 PM
|
||||
|
||||
|
Well, I was wrong. I am still getting the intermitant recording conflicts. As before, it seems as if SageTV suddenly forgets that it has a network encoder available to it for recording. But I noticed a new thing today, both the primary SageTV recorder and the network encoder were both recording shows when started to view the show that the primary encoder was recording. This action caused the conflicts to pop up again and it took me about 20 seconds to make them go away. When I went to watch the show recorded by the network encoder, there was a gap of about 20 seconds roughly in the place where the conflicts popped up.
This never happened with SageTV 2.0, only after I upgraded to 2.1 did it start to occur. Anyone have any ideas? Karen
__________________
Intel Pentium 4@2.4 GHz Gigabyte GA8-IHXP 768 MB RDRAM NVidia GeForceX 5700 Hauppage WinTV PVR-350 1 TB Hard Drive space
|
|
#5
01-08-2005, 07:14 PM
|
||||
|
||||
|
You might try setting tuner priorities in properites file.
__________________
Click here for Pic's & spec's of my SageTV Server & HTPC Client
|
|
#7
01-09-2005, 03:44 AM
|
||||
|
||||
|
mdmint,
Thanks for the suggestion, but I already have tuner priorities set such that the tuner in the SageTV computer has the highest priority. The network encoder is used only when there is a conflict. Karen
__________________
Intel Pentium 4@2.4 GHz Gigabyte GA8-IHXP 768 MB RDRAM NVidia GeForceX 5700 Hauppage WinTV PVR-350 1 TB Hard Drive space
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
