|
|
|||||||
| Hardware Support Discussions related to using various hardware setups with SageTV products. Anything relating to capture cards, remotes, infrared receivers/transmitters, system compatibility or other hardware related problems or suggestions should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
07-27-2005, 09:06 AM
|
|||
|
|||
|
BTC9019URT wireless keyboard
i'm using the 9019 to control my EVIA based HTPC in my living room.
it does a great job for navigating windows and SageTV control screens. however, i have not been able to figure out how to teach STV to listen to the multimedia keys on the top row so i can control the 'player' functions. thanks in advance for your advice... 
|
|
#2
07-27-2005, 10:27 AM
|
||||
|
||||
|
BTW: If those keys simply send the same sort of commands as most such multimedia keys, then they should be sending standard Windows messages that SageTV already knows how to respond to. (As covered in the SageTV Commands section of Chapter 5 in the PDF manual in your SageTV dir.) I'm just not certain whether SageTV needs to have focus when those buttons are in use. Also, I think it is possible that if some other program is running which uses those keys, the commands may not get passed along to SageTV.
- Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request.
|
|
#3
07-27-2005, 02:23 PM
|
||||
|
||||
|
you will need BTC's "Key Maestro" that came with the keyboard. You can then assign windows commands (as andy said) to the hotkeys for whatever you want.
Most of them are actually correct by default though.
__________________
If you're not cheating, your not trying... My sage rigs: Server - Windows 2003, Intel 865 PERLL w/ P4 3.2g 1gb ram, 3-PVR250, 3-PVRUSB's, 1 Skystar2, 1 twinhan 102g, 1 starbox DVB-S Cards. Evo network QAM encoder. 1.2TB storage 6.x server + MTSAGE for DVB Client 1/Master BR - MediaMVP running a 30" Olevia LCD TV. Client 2/Front Room - Shuttle ST61G4 XPC 1gig ram, 60gb HD, BTC9019 wireless keyboard/mouse & Harmony 880. 6.x client. GF6600GT driving a Sony WEGA 55" rear projection tv.
|
|
#4
07-27-2005, 09:31 PM
|
|||
|
|||
|
hi guys,
thanks for the tips. more detailed info after experimenting further. volume keys work fine. mute works fine stop key works fine. rewind key must be held down to work forward key must be held down to work play/pause causes WindowsMediaPlayer install to launch ?! it must be that a default is set to WMP. where do i look ?
|
|
#5
07-27-2005, 10:39 PM
|
||||
|
||||
|
as stated before. Go find "key maestro"
__________________
If you're not cheating, your not trying... My sage rigs: Server - Windows 2003, Intel 865 PERLL w/ P4 3.2g 1gb ram, 3-PVR250, 3-PVRUSB's, 1 Skystar2, 1 twinhan 102g, 1 starbox DVB-S Cards. Evo network QAM encoder. 1.2TB storage 6.x server + MTSAGE for DVB Client 1/Master BR - MediaMVP running a 30" Olevia LCD TV. Client 2/Front Room - Shuttle ST61G4 XPC 1gig ram, 60gb HD, BTC9019 wireless keyboard/mouse & Harmony 880. 6.x client. GF6600GT driving a Sony WEGA 55" rear projection tv.
|
|
#6
07-30-2005, 11:59 AM
|
|||
|
|||
|
hi guys,
thanks for all the help, it's working great now. unchecked Enable AutoPlay. using KeyMaestro, mapped MM keys to send the proper combination codes. now on to how i could have possibly screwed up the web interface installation...
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Linear Mode
