|
|
|||||||
| Hardware Support Discussions related to using various hardware setups with SageTV products. Anything relating to capture cards, remotes, infrared receivers/transmitters, system compatibility or other hardware related problems or suggestions should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
07-10-2008, 09:11 AM
|
|||
|
|||
|
HD PVR No Signal Occasionally
I have been running my 2 HD-PVR's for quite a couple weeks straight now but i have been getting a No Signal in sage occasionally. All I have to do to correct this is just push the power button on the front of the HD-PVR that is having the problem let it sit for a couple seconds and then power it back on and then all is well again. Both of my units are Rev C2 and I only capture at 1080i and analog audio if that helps. Anyone else have any similiar issues?
Jayson
__________________
ESXi Host Intel Xeon x3440 on Intel S3420PLX, 4GB RAM, 80GB Primary Server:2 CPU's and 2GB memory Allocated, 15GB Virtual Primary, 1.5 TB RDM Physical Disk, A180 using VMDirectPath, 1 xHDHR Headless ArchLinux 2.6.34 64-bit, SageTV 7.0.15 Sun JRE 1.6.0_20 Comskip&PlayonWindows XP 2CPU and 1GB Ram Allocated Clients: 1 Media MVP and 2 STX-HD100 
|
|
#2
07-10-2008, 06:51 PM
|
||||
|
||||
|
I am having this same issue with my one remaining unit. It is Rev. C2 and was sent back for the heatsink and fan install. (I'm waiting on the other two to be fixed and returned to me.)
I am thinking about going back to the original driver release to see if that changes anything. S
|
|
#3
07-24-2008, 10:51 AM
|
|||
|
|||
|
I have the same problem as well. It seems to happen (very occasionally) when I change channels.
|
|
#5
07-24-2008, 12:26 PM
|
||||
|
||||
|
Never had no signal, but mine just seems to stop recording occasionally.
__________________
Server: AMD 9600 Phenom on XP, Gigabyte GA-MA78GPM, 2GB RAM, 320+250+500 GB SATA drives, HDHomeRun Prime, HD-PVR x.5.1, Paterson serial Client/Encoder:AMD 3800+ X2, 512 MB RAM, ATI X1650 XT, nMediaPC case, Hauppauge HD-PVR, Cyberlink/ArcSoft decoders, USB-UIRT Client/Encoder: AMD 3800+ X2, 512 MB RAM, 6150 graphics, nMediaPC case, ArcSoft decoders Client: HD300, Asus Pundit P1-AH1, AMD 3800+ X2 CPU, 1 GB RAM, 6150 graphics, ArcSoft decoders Backup: Synology SageTV version: FINAL
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| HD PVR Audio our of sync | Bandit | Hardware Support | 4 | 08-02-2008 06:50 PM |
| Sage + DirecTV HD DVR question | subhadipsas | Hardware Support | 11 | 07-08-2008 11:45 PM |
| Switching channels between HD and SD with HD PVR | padre | Hardware Support | 13 | 06-15-2008 08:44 AM |
| Best comcast box for use with HD PVR? | Sam | Hardware Support | 4 | 06-12-2008 07:33 PM |
| AUUUGH I Give UP!!! | TripleTapper | SageTV Media Extender | 46 | 01-03-2006 02:35 PM |
Linear Mode
