|
SageTV EPG Service Discussion related to the SageTV EPG Service used within SageTV. Questions about service area coverage, channel lineups, EPG listings, XMLTV, or anything else related to the service or programming guide data for SageTV should be posted here. |
|
Thread Tools | Search this Thread | Display Modes |
#1
|
|||
|
|||
Missing Channel
For some reason one channel (a channel I watch sometimes) is missing from the channel lineup on the guide. I have all the channels enabled and I'm in the U.S. How can I get that channel back?
|
#2
|
||||
|
||||
All the channels in Channel Setup are enabled?
How many tuners do you have and, therefore, how many lineups? If a network is on both lineups, but they have different channel numbers, the LiveTV Guide will only list one of those numbers. If the channel simply isn't listed in Channel Setup... then perhaps there's a glitch in the EPG data for that provider. - Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request. |
#3
|
|||
|
|||
I have on tv tuner and I think I have one channel lineup.
|
#4
|
|||
|
|||
I fixed it. I went through channel setup again and that channel popped up. I guess it was just a glitch, but no data for the channel.
Last edited by sweet_pea; 12-24-2004 at 08:16 PM. Reason: It didn't look right before |
#5
|
|||
|
|||
missing channel... multiple sources... multiple EPG sets
Opus4, You mention Sage will only show one of the channels that exist on different tuner setups if the guide data matches. Is there any way to have the Sage guide show the both channels?
Trying to make this question clearer: tuner 1: channel 10 NickJr tuner 2: channel 99 NickJr Right now only channel 10 is showing up. I would like both channel 10 and 99. Is this possible? If not how do I force Sage to map the channel to channel 99 instead of 10? (besides priority of the tuner as there are other channels I want recorded off the first tuner ahead of the second) |
#6
|
||||
|
||||
See p. 40 in the v2.2 manual. The channels will be listed once, but they will both actually be available and used. In your case: if the source w/channel 10 is already in use, channel 99 on the other one wil be used if you try to watch NickJr.
I don't remember the priority regarding which channel number gets listed, but I don't believe it is the same as the tuner's merit (priority). - Andy
__________________
SageTV Open Source v9 is available. - Read the SageTV FAQ. Older PDF User's Guides mostly still apply: SageTV V7.0 & SageTV Studio v7.1. - Hauppauge remote help: 1) Basics/Extending it 2) Replace it 3) Use it w/o needing focus - HD Extenders: A) FAQs B) URC MX-700 remote setup Note: This is a users' forum; see the Rules. For official tech support fill out a Support Request. |
#7
|
|||
|
|||
That's dissapointing... I'm using both analog cable and digital cable as sources. On analog cable all the kids channels are spread all over the place. On digital cable they are all together which makes it easier for the kids to find what they want (part fo the WAF here!). Sure would be nice if I could take advantage of the analog cable for recording conflits but only have the digital cable channel numbers show up in the EPG. Anyone have any ideas?
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|