|
|
|||||||
| Hardware Support Discussions related to using various hardware setups with SageTV products. Anything relating to capture cards, remotes, infrared receivers/transmitters, system compatibility or other hardware related problems or suggestions should be posted here. |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
#1
11-06-2011, 07:09 PM
|
||||
|
||||
|
Hauppauge HD-PVR (USB) IR blaster issue
I've been fooling with my Time Warner STB over the last few days, occasionally disconnecting the HD-PVR to play with some other devices. When I hooked everything back up, I noticed that SageTV+HD-PVR is no longer sending a signal to change the channel on the STB. I schedule a program, no channel change occurs, but the HD-PVR starts recording anyways (on whatever channel the STB happened to be on). Even after reboot(s), still no success.
I then shutdown SageTV and was able to get the IR Blaster working fine with the "BlastCfg" Utility, pretty much immediately. I'm not sure where to look to determine where the problem is. Any ideas would be much appreciated. Note: I also have an original 2-tuner HDHR device running along side the HD-PVR, both of them active tuners in SageTV. 
|
|
#2
11-06-2011, 07:24 PM
|
||||
|
||||
|
Scratch that. It decided to start working again.
Now ... where do I buy that USB-IRT?
|
|
#4
11-07-2011, 01:25 PM
|
||||
|
||||
Before You Spend The Money...
I am using both the USB IRT and the HD-PVR blaster.
See if either of these links help. http://forums.sagetv.com/forums/show...light=irremote http://forums.sagetv.com/forums/show...ghlight=remote BTW, after fooling with the HD-PVR, disconnecting and reconnecting, I recommend a reboot. It also helps if you check the Hauppauge Blaster Config utility and make sure it is set for the correct STB before rebooting. Last edited by doncote0; 11-07-2011 at 01:27 PM.
|
|
#5
11-07-2011, 01:36 PM
|
||||
|
||||
|
I use the HD-PVR blaster as well and I have found that if I disconnect/connect or power cycle the HD-PVR that minimally, restarting the SageTV service is needed for the blaster to work properly again.
__________________
SageTV Server 7.1.x w/Gemstone and Plex Home Theater v1.0.10 w/PlexPass
HD-PVR w/v1.5.6 drivers / Hauppauge IR blaster / FiOS Extreme HD / Motorola QIP6200 / SPDIF+720p Fixed Output on HP Media Center 8400F (Phenom 9500 QuadCore 2.2GHz, nVidia GeForce 8500 GT) via Olevia 247TFHD/Onyko TX-SR606/Harmony 550/HP MediaSmart EX490 WHS w/12TB Plex Media Server v0.9.9.5 on HP Touchsmart Envy 23 d16qd Sonos Play:3, Connect / SimpleTV v2 / Roku 2 XS+Plex / iPhone 5 / iPad 2
|
|
#6
11-07-2011, 01:52 PM
|
||||
|
||||
|
Good Info
Quote:
|
|
| Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
|
|
Similar Threads
|
||||
| Thread | Thread Starter | Forum | Replies | Last Post |
| Hauppauge IR Blaster Control Issue After Awaking From Standby | sscumming | SageTV Beta Test Software | 1 | 11-10-2010 09:53 PM |
| Ubuntu 10.04 HDPVR IR Blaster Issue | lyroy | SageTV Linux | 12 | 06-16-2010 07:21 PM |
| IR Blaster Issue with Sage, Hauppauge 1600 (v1199( | bglines | Hardware Support | 1 | 04-25-2010 07:59 PM |
| Tuning Issue with DISH and Hauppauge IR Blaster | Severvip | Hardware Support | 11 | 07-29-2008 09:27 AM |
| IR Blaster issue with RC6 | zoop | SageTV Linux | 2 | 03-24-2007 02:09 PM |
Linear Mode
